|
Trend Door ClampHolds door while drilling and fitting locks. No set-up time needed. No more searching and alternative door stops. Padded to prevent door and floor damage. For doors up to 55mm thick.... |
£37.95 More Information » |
||
|
Trend Door Holder StandHolds door on its edge while routing hinge recess & mortise for locks. Holds door securely. Non-scratch base. Adjustable clamp for doors 32mm to 55mm thick. Allows door to be tilted back to assist fitting into frame. Maximum door weight 58kg.... |
£78.95 More Information » |
||
|
Trend Double Bearing Guided Trimmer Routing Cutter 19.1mm 50mm 1/2"Ball bearings fitted to both nose and shank. Allows templates to be placed either on top or the bottom of the material, for ease of routing. Allows for irregular grained timber to be profiled more easily, by turning component other way up. Speci... |
£103.95 More Information » |
||
|
Trend Dovetail Router Cutter 12.7mm 10mm 1/2"For dovetail joints and sliding dovetails. Can be used with Ref.10/40 butterfly 14 degree spline cutter. Specifications • Shank Diameter: 1/2 • Dia Metric: 12.7 • Dia Imperial: 1/2 • Cut Length Metric: 10 • Cut Length Impe... |
£36.95 More Information » |
||
|
Trend Dovetail Router Cutter 19.1mm 19.1mm 1/2"For dovetail joints and sliding dovetails. Can be used with Ref.10/40 butterfly 14 degree spline cutter. Specifications • Shank Diameter: 1/2 • Dia Metric: 19.1 • Dia Imperial: 3/4 • Cut Length Metric: 19.1 • Overall Lengt... |
£45.95 More Information » |
||
|
Trend Dovetail Router Cutter 25.4mm 25.4mm 1/2"For dovetail joints and sliding dovetails. Can be used with Ref.10/40 butterfly 14 degree spline cutter. Specifications • Shank Diameter: 1/2 • Dia Metric: 25.4 • Dia Imperial: 1 • Cut Length Metric: 25.4 • Overall Length ... |
£48.95 More Information » |
||
|
Trend Dowel Centre Point PackSix pack of metal dowel centre points of diameter 6mm, 8mm & 10mm. Pair of 6mm, 8mm and 10mm diameter. Dowel centres fit into blind holes to allow lining up for the mating hole. Place end of dowel centre in the bored dowel hole in one piece of woo... |
£4.95 More Information » |
||
|
Trend Down Cut Shear Two Flute Router Cutter 12.7mm 38mm 1/2"Tungsten Carbide Tipped. Two flute cutter with a positive shear angle (down-cut) for fast cutting and fine finish. Ideal for grooving & trimming veneer finishes & laminated boards. Down cut feature stops break out on top edge. Has a 4 degree she... |
£52.95 More Information » |
||
|
Trend Down Cut Shear Two Flute Router Cutter 12.7mm 50mm 1/2"Tungsten Carbide Tipped. Two flute cutter with a positive shear angle (down-cut) for fast cutting and fine finish. Ideal for grooving & trimming veneer finishes & laminated boards. Down cut feature stops break out on top edge. Has a 3 degree she... |
£54.95 More Information » |
||
|
Trend Down Cut Shear Two Flute Router Cutter 9.5mm 25mm 1/2"Tungsten Carbide Tipped. Two flute cutter with a positive shear angle (down-cut) for fast cutting and fine finish. Ideal for grooving & trimming veneer finishes & laminated boards. Down cut feature stops break out on top edge. Has a 4 degree she... |
£40.95 More Information » |
||
|
Trend Down Cut Shear Two Flute Router Cutter 9.5mm 25mm 1/4"Tungsten Carbide Tipped. Two flute cutter with a positive shear angle (down-cut) for fast cutting and fine finish. Ideal for grooving & trimming veneer finishes & laminated boards. Down cut feature stops break out on top edge. Has a 4 degree she... |
£37.95 More Information » |
||
|
Trend Drawer Lock Jointer Router Cutter 25.4mm 12.7mm 1/2"To increase gluing area producing a strong joint in drawer production. Specifications • Shank Diameter: 1/2 • Dia Metric: 25.4 • Dia Imperial: 1 • Cut Length Metric: 12.7 • Cut Length Imperial: 1/2 • Overall Length Metr... |
£51.95 More Information » |
||
|
Trend Drawer Pull Radius Router Cutter 25mm 32mm 1/2"The long cut depth of these cutters allows them to produce under-cut finger grooves. Specifications • Shank Diameter: 1/2 • Dia Metric: 25 • Cut Length Metric: 32 • Overall Length Metric: 70 • Radius 1 Metric: 12.5... |
£93.95 More Information » |
||
|
Trend Drawer Pull Router Cutter 19mm 13mm 1/4"An initial cut with a straight cutter is required to produce the drawer pull profile. Specifications • Shank Diameter: 1/4 • Dia Metric: 19 • Cut Length Metric: 13 • Overall Length Metric: 48 • Radius 1 Metric: 4... |
£107.95 More Information » |
||
|
Trend Drawer Pull Router Cutter 38mm 17mm 1/2"An initial cut with a straight cutter is required to produce the drawer pull profile. Specifications • Shank Diameter: 1/2 • Dia Metric: 38 • Dia2 Metric: 22 • Cut Length Metric: 17 • Overall Length Metric: 61 • Radius ... |
£120.95 More Information » |
||
|
Trend Drawer Pull Router Cutter 44.8mm 25.4mm 1/2"An initial cut with a straight cutter is required to produce the drawer pull profile. Specifications • Shank Diameter: 1/2 • Dia Metric: 44.8 • Dia2 Metric: 24 • Cut Length Metric: 25.4 • Overall Length Metric: 64 • Rad... |
£133.95 More Information » |
||
|
Trend Drawer Pull Router Cutter 45mm 17mm 1/2"An initial cut with a straight cutter is required to produce the drawer pull profile. Specifications • Shank Diameter: 1/2 • Dia Metric: 45 • Dia2 Metric: 24 • Cut Length Metric: 17 • Overall Length Metric: 60 • Radius ... |
£147.95 More Information » |
||
|
Trend Easy ScribeHandheld scribing tool for architrave, skirting, scribing doors, scribing worktops, setting hinge recess depth etc. Articulated arm allows the required offset to be set precisely from 1mm to 40mm giving full flexibility. Use for a multitude of appl... |
£46.95 More Information » |
||
|
Trend Easyscribe Graphite ClampSpare graphite clamp assembly for the Easyscribe tool.... |
£3.49 More Information » |
||
|
Trend Easyset Bearing Guided Classic Combination Set 41mm 11mm 1/2"These tools produce the same type of joint & use the same components as the combination PSC sets. Both parts of the joint are cut by only changing the cutter height. No reassembly of parts is required, to convert the tool from scribing mode to prof... |
£147.95 More Information » |